Type 1018.2 USB - PC GENERATOR BOARD

Type 1018.2

Type 1018.2 USB - PC GENERATOR BOARD

The PC GENERATOR BOARD Type 1018.2 combines the power supplies for fundamental electrical engineering and electronics experiments on one board. Via the integrated USB interface and operator software, the output signals can be set precisely from a PC and displayed on a beamer at the same time. It can be used with or without PC support.

  • All power supplies for fundamental experiments on one board
  • Integrated DC, AC and three-phase current sources plus function generator
  • Short-circuit proof outputs with LED monitoring
  • USB interface with operator software for precise PC control
  • Signals can be projected on a beamer at the same time
  • Useable with and without PC support
Datasheet (PDF) Data sheet Experiment manuals, contents Software Send Inquiry

Purpose and operating principle

The PC GENERATOR BOARD Type 1018.2 is a compact training system for basic experiments in electrical engineering and electronics.

DC, AC and three-phase current sources as well as the function generator are integrated and can be controlled directly on the board or via PC.

  • Integrated USB interface with operator software
  • Output signals can be adjusted precisely on the PC
  • Signals can also be projected on a connected beamer
  • Useable with and without PC support

Construction, technical features and accessories

The front panel is made of 5 mm thick laminate in matt blue with white symbols for the built-in function groups. The rear is protected by a grey plastic cover and allows an ergonomically favourable angle on the table.

All outputs are short-circuit proof and LED-monitored; the connections are provided via 2 mm and 4 mm jacks.

  • Optional measuring interface Type 1018.4 with two current and two voltage inputs
  • Optional USB oscilloscope Type 1018.5 for time and frequency domain display
  • Accessory set Type 1018.11 with storage board, resistors, capacitors, semiconductors and transformer coils
  • Accessory set Type 1018.11.1 with connecting leads and plugs
  • Universal assembly board Type 1012.1 or Type 1012.2
  • IC BOARD Type 3530 for additional experiments with commercial components
  • 2 mm and 4 mm jacks for connection
Mains voltage
230 V AC / 115 V AC (110 V AC), 50 ... 60 Hz; appr. 70 VA
DC voltages
+15 V (± 5 %); 800 mA; -15 V (± 5 %); 800 mA; +5 V; 100 mA; 0 ... 25 V; 300 mA
AC voltage
24 V AC; 100 mA
Function generator sinewave
UPP 0 ... 20 V; f appr. 1 Hz ... 250 kHz; Ri 60 Ohm
Function generator squarewave, positive
5 V (TTL); f appr. 1 Hz ... 250 kHz; Ri 60 Ohm; V = 2
Function generator squarewave, symmetrical
UPP 0 ... 20 V; f appr. 1 Hz ... 250 kHz; Ri 60 Ohm; V = 2
Function generator triangular wave, symmetrical
UPP 0 ... 20 V; f 1 Hz ... 250 kHz; Ri 60 Ohm
Three-phase current generator
Phase voltage 7 V (eff.); line voltage 12 V (eff.); line current max. 50 mA; frequency appr. 50 Hz
Jacks
2 mm and 4 mm jacks
Mechanical data
Front panel made of 5 mm laminate, matt blue, white symbols; rear protected by a grey plastic cover; ergonomically favourable angle on the table
Dimensions / weight
266 x 297 x 120 mm (w x h x d) / appr. 2.8 kg
Optional measuring interface
Type 1018.4; two current and two voltage inputs
Optional USB oscilloscope
Type 1018.5; time and frequency domain display
Accessories required (optional)
Type 1018.11, Type 1018.11.1, Type 1012.1 or Type 1012.2
Accessories recommended (optional)
Type 1018.4, Type 1018.5, Type 3530

More Products in This Category