Type 5125
POWER BOARD Type 5125
The POWER BOARD from hps SystemTechnik provides a demonstration and training system covering the entire field of power electronics. Connected to a single-phase mains supply, the required three-phase AC voltage is generated internally. The temperature and brightness controlled system Type 5125.5 is included in the scope of delivery.
- Complete power electronics system in a single board
- Built-in three-phase source generated internally from the single-phase mains
- Plug-in field for temperature and brightness controlled system Type 5125.5 included in delivery
- All experiments at 12 V safety extra-low voltage
- Four-quadrant operation with H-bridge (MOS-FET) or anti-parallel thyristor bridges
- Can be combined with PID BOARD and MOTOR BOARD
Application and system concept
With the POWER BOARD, hps SystemTechnik provides a demonstration and training system for experiments covering the entire field of power electronics. The board is connected to a single-phase mains supply while the required three-phase AC voltage is generated internally.
The system is designed so that all experiments are carried out at 12 V safety extra-low voltage. This makes the board suitable both for introductory training and for more advanced laboratory work in power electronics.
Functional blocks and measurement options
The POWER BOARD combines uncontrolled and controlled rectifiers, phase-angle control units, burst firing control, pulse-width modulation and an H-bridge with power MOS-FETs in one compact unit.
All important measurement points are available on sockets. Galvanically isolated firing-pulse outputs via firing transformers and bridgeable shunts in the load-current branches enable reproducible earth-free measurements.
Combinations and accessories
The temperature and brightness controlled system Type 5125.5 is included in the scope of delivery. In addition, the POWER BOARD can be combined with the PID BOARD and the MOTOR BOARD for four-quadrant drive experiments and control tasks.
The documentation recommends experiment manual Type V 0121 “Introduction to Power Electronics” as well as accessory set Type 5125.1 with connecting leads and plugs.
- Phase-angle control II with input for a negative setpoint
- Galvanically isolated firing pulse outputs via firing transformers
- Bridgeable shunts for current measurement in the load-current branches
- Phase-angle control I with measurement points available on sockets for single- and multi-pulse operation
- PWM control for investigating smoothing at variable fundamental frequency
- Adapter field for 4 mm to 2 mm transitions and BNC adapters
- Mains voltage
- 230 V AC / 115 V AC (110 V AC), 50...60 Hz, 80 VA
- Mains switch
- ON / OFF with indicator light
- DC supply
- +/- 15 V DC; 2.5 A
- AC supply (L1)
- 12 V AC; 1 A
- Signal generator
- f = 2...100 Hz (for sine-modulated PWM)
- Three-phase source
- Switchable for M3 or B6 circuit, UA eff = 12 V DC
- Galvanic isolation
- All power supplies galvanically isolated from each other
- Controllers
- Phase-angle control I, II and III; burst firing control; pulse-width modulation; switching logic for circulating-current-free four-quadrant drive; GTO pulse shaper
- Rectifiers
- Uncontrolled rectifiers; controlled rectifiers (thyristors); H-bridge (power MOS-FET)
- Additional semiconductors
- 1 x diode, transistor, GTO thyristor, TRIAC
- Resistive load
- 27 Ohm
- Inductive load
- 20 mH
- Capacitive load
- 47 µF
- Temperature actual value
- PTC resistor
- Light actual value
- LDR resistor
- Heating and light source
- Incandescent lamp 12 V / 5 W
- Front panel
- 5 mm laminated material, matt blue, white engraving
- Dimensions (board)
- 532 x 297 x 130 mm (W x H x D)
- Weight (board)
- approx. 5.4 kg
- Dimensions (box version)
- 585 x 425 x 155 mm (with Type 5125.20)
- Weight (box version)
- approx. 8.8 kg
- Dimensions (control module 5125.5)
- 37 x 56 x 35 mm (W x D x H), without connector
- Weight (control module 5125.5)
- approx. 65 g
- Recommended accessories
- Experiment manual Type V 0121 “Introduction to Power Electronics”; accessory set Type 5125.1 (connecting leads and plugs)
- AC mains: Uncontrolled half-wave rectifier
- AC mains: Uncontrolled bridge rectifier
- AC mains: Half-controlled bridge rectifier
- AC mains: Fully controlled bridge rectifier
- AC mains: Line-commutated inverter
- AC mains: Two fully controlled bridge rectifiers anti-parallel with circulating-current-free circuit and optical indication via 2 LEDs
- AC mains: Burst firing control (cycle control)
- DC mains: Basic pulse-width modulation (PWM) circuits
- DC mains: PWM with H-bridge, DC-modulated
- DC mains: PWM with H-bridge, sine-modulated
- GTO (Gate-Turn-Off): Firing pulse conditioning for the GTO
- GTO (Gate-Turn-Off): GTO as a DC chopper
- Three-phase mains: Uncontrolled rectifier (M3)
- Three-phase mains: Uncontrolled rectifier (B6)
- Three-phase mains: Controlled rectifier (M3)
- Three-phase mains: Controlled rectifier (B6)
- Control module 5125.5: Temperature control via PTC resistor with incandescent lamp (12 V / 5 W) as heat source
- Control module 5125.5: Light control via LDR resistor with incandescent lamp as light source
